Nicole
2005-08-21, 11:29am
Nicole’s Square Tabular Bead Tutorial
I started making these beads in ’97 because I had a really hard time getting my beads on center. (I was having way too much fun in class to pay attention or get the details down). The one lesson that stuck in my head was “if it doesn’t turn into what you want fairly quickly, turn it in to something else” So there I was in my little studio flattening the heck out of most of my beads! ‘Not round I squish you!’ It wasn’t until I got some really nice mashers that the shape really took off for me. I use a super sweet pair of Carlo Donna mashers that I picked up at Pilchuck. Carlo Donna Rocks!!!!
“Special’ Tools needed – One pair of parallel mashers – Torch Marver – Graphite paddle
1. Make a basic bead – let it cool a little bit before step two
2. Shape the bead into a cylinder – I use my torch marver and graphite paddle, gently reheat to a warm glow after shaping.
3. Slowly Press flat with the mashers – I hold up the bead and look through the mashers as I press. This gives me a very good idea of how thin the bead should be.
4. Square up the sides with the mashers. Square up the top and bottom too. A bit of reheating might be necessary.
5. Firepolish the chill marks off the tabular bead. You may need to reshape the bead a bit at this point. Be gentle with the heat to prevent too much distortion.
Tips:
It will be easier to make a square bead if you start with a very round bead. It should be as wide as it is round. A narrow roundel just won’t cut it.
I use my torch marver and paddle together to shape the cylinder. I place the paddle on edge against the bottom of the torch marver. This boxes in the bead and makes it easier to shape.
Some patterns and decorations are applied before the shaping is done, i.e. Frit, Silver Foil, and Silvered Ivory. It you press slowly it shouldn’t distort the pattern too much.
I think the rule of thumb with bead is simple. ‘If at first you don’t succeed, try, try again. I didn’t figure this shape out in an hour. It took months/years of practice to get it right.
I should mention that I didn't 'invent' this shape. It's been around forever and the Venetians currently produce beads just like this.
Hopefully I’ll get a chance to add some step-by-step photos to this soon. Here are a few images of the square beads for you to enjoy!
I started making these beads in ’97 because I had a really hard time getting my beads on center. (I was having way too much fun in class to pay attention or get the details down). The one lesson that stuck in my head was “if it doesn’t turn into what you want fairly quickly, turn it in to something else” So there I was in my little studio flattening the heck out of most of my beads! ‘Not round I squish you!’ It wasn’t until I got some really nice mashers that the shape really took off for me. I use a super sweet pair of Carlo Donna mashers that I picked up at Pilchuck. Carlo Donna Rocks!!!!
“Special’ Tools needed – One pair of parallel mashers – Torch Marver – Graphite paddle
1. Make a basic bead – let it cool a little bit before step two
2. Shape the bead into a cylinder – I use my torch marver and graphite paddle, gently reheat to a warm glow after shaping.
3. Slowly Press flat with the mashers – I hold up the bead and look through the mashers as I press. This gives me a very good idea of how thin the bead should be.
4. Square up the sides with the mashers. Square up the top and bottom too. A bit of reheating might be necessary.
5. Firepolish the chill marks off the tabular bead. You may need to reshape the bead a bit at this point. Be gentle with the heat to prevent too much distortion.
Tips:
It will be easier to make a square bead if you start with a very round bead. It should be as wide as it is round. A narrow roundel just won’t cut it.
I use my torch marver and paddle together to shape the cylinder. I place the paddle on edge against the bottom of the torch marver. This boxes in the bead and makes it easier to shape.
Some patterns and decorations are applied before the shaping is done, i.e. Frit, Silver Foil, and Silvered Ivory. It you press slowly it shouldn’t distort the pattern too much.
I think the rule of thumb with bead is simple. ‘If at first you don’t succeed, try, try again. I didn’t figure this shape out in an hour. It took months/years of practice to get it right.
I should mention that I didn't 'invent' this shape. It's been around forever and the Venetians currently produce beads just like this.
Hopefully I’ll get a chance to add some step-by-step photos to this soon. Here are a few images of the square beads for you to enjoy!