|
Hello Chad,
Can you please send me the tutorial? My email address is chimehk@yahoo.com Thanks, Chimehk |
Quote:
|
|
could I have a link to the tutorial please? TX Laura
|
|
Quote:
thanks! Jeanette |
Hi Chad, my URL is ct26nguyen@usfamily.net i'd like to have this tut too. The end of my name is 'u'. Got it. Thanks.
|
Is the offer still open? I'd really like a copy of the tutorial.
Thank you so much, DeAnn ak92ATmtaonline.net replace the AT with @ appreciated so much! |
Chad, Have you thought about putting it in pdf and loading that on your site? otherwise I'd be happy to host it for you just send me the file (the whole page please, I hate doing html) and I'll upload it
camie at andersonsplace dot net |
I would REALLY like someone to send me the tutorial too!!
|
Well, still after a year, I've not seen hide nor hair of this tutorial, so would somebody who does have it send along my way...much appreciated.
FiredDesires@aol.com |
|
I would like a copy too, please!
rosiescreations2003@yahoo.com |
Got it! Thanks!!!
|
tutorial
Please if you get the time I would really like it as well. kathiejohannes@yahoo.com
|
Raticello
Chad, Would you please send me the tutorial? Much appreciated! Volker
maximillianmutz@aol.com |
I don't have the tutorial any more. We had a hard drive failure a few months back and I lost everything. That was one of the things I lost.
I got it from The Flow Magazine - www.theflowmagazine.com - so you can check there. Perhaps they have it online, or can tell you what issue it was in. |
could anyone send me a tutorial as well---this could be fun ubrad@aol.com Thanks
|
This is a different way...
I prefer this method to the other one for two reasons: I think the finished result is cleaner, and I like the color being trapped between two layers of glass.
Take a point of 1"HW, about four inches long. Open one handle, draw lines down the length of the tube, and twist. Make sure the twist is consistent along the length of the tube. Now open the other handle (so they're BOTH open) and jack constrict/jack downin the middle until it's completely closed. You now have two sections of tubing with handles that are connected by a solid piece in the middle. Blow one side slightly into a bubble, and then rip off your point handle, leaving it open, even, and round on the end. Now flare this side out like a foot, but keep going. Change the angle so it starts to fold over back over the other section of tube (the one you didn't blow out. Work it from the end down to avoid trapping air bubbles. After you've got it worked into one solid bubble, blow it out a little and rip off the end to clean up the termination point. I don't check this board that often, but feel free to email me at christopher_platt@csumb.edu with any questions. Chip |
|
|
Quote:
Quote:
|
Opposing Spirals
Chad
Is this a version or Opposing Spirals that are on the Corbin Freeman marble video? Gloria |
Quote:
Like what Chris Roesinger does: http://www.glassartists.org/Gal17047..._s_Gallery.asp |
Hey Cosmo,
can I get a copy of that tutorial on rattis? |
Quote:
Quote:
|
Poor Chad...kinda makes you wanna bang your head against a wall...doesn't it?
|
This is proof positive that peeps do not read a thread all the way through!
Yes, poor Chad...I apologize for sounding so curt in an earlier thread about never having received the tutorial......you can't send what you don't have any longer....thanks for your intended generosity anyhooooos...at least you found what issue of the Flow that it is in...whoohooooo |
Hi, may I have the tutorial? thanks a lot
|
|
| All times are GMT -7. The time now is 1:06pm. |
Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.