Consistant bead sizes
Ive been wanting to post this tip for a while now and just now got around to taking pics.... ignore the background..lol... ( my tables messy)
But here's my tip for consistant sized beads.... Use this tool.. ( its a dremel cutting tool) Cut pieces in uniform sizes.... See Below for how to do this. Punty them up..( Punty means to attatch the short glass to a mandrel to hold it) . I use a old mandrel i have bent.. you must HEAT the mandrel too for it to stick.. use your fingers to hold glass unless its very short then use your needlenose. Melt it as usual.. * Ive been asked to expand on this part.* WEhen you wind your glass, use a small footprint ( which is where your glass touches the mandrel) Wind it up onto itself like a disk. Melt it slowly, not letting it fold back upon itself. Use gravity, it is your friend. And you can take the bead out of the flame to roll slowly to even it out. Dont "Spin it" go slow, letting it take shape by itself. It will then form a nice Dimple ( the indented part, like a donut) and will shape up nicely into a round. Viola! consistant bead sizes. :) Hope this helps someone. I know i had a lot of trouble with consistant sizes before I McGyvered this out. |
excellent tip.
|
Good idea! I usually get an old bead out (even a wonky works) and try to make beads that match that size.
|
GASP! Isn't that cheating?
I think you should go back to winging it and praying to the glass gods - like the rest of us. (good tip - gotta try that :-)) |
I just make a bunch of beads on the same mandrel :)
|
i usually make 3 or 4 beads and hope that two are sorta close . . . or don't they call that the graduated set?
|
Genius!
Jen |
you can cut glass with those things??? cool idea!
|
great tip Tess!
|
Quote:
Ill go take some pics and show you........ |
|
Great tip Tess,
If you have glass nippers, they work great too! (that's what I use to cut my pieces)! |
Well this isnt meant for those of you that know what they are doing! :kiss:
Nippers is a great idea too! I just have seen the question a lot from newbies and us tweeners. So thought id pass along the idea:) |
Tess,
That's a great idea!!! I can hardly wait to try it. I have trouble with an even foot print, much less with consistant sizes. Thanks so much for sharing! Susan |
Wel it is an AWESOME idea Tess! You GO girl!
Quote:
|
Wow...what a great tip! Thank you thank you thank you. I've been drawing on my marvering plate, trying to measure using a metal ruler, etc...this looks like a really great way!
|
I never thought about using a dremel. One of my first tools was glass cutters (nippers). I was told to buy them at the hardware store. I've been making beads for 13 years - the nippers still work perfectly. I have the round wheel kind and the straight edge kind (like this best). For same size bead I have a friend who marked her rod. I keep a brass gauge on my table and measure the base bead before I decorate - need to be about 1mm narrower but exact length. Before I put bead in kiln I check it again with the gauge. Works for me!
|
The Gauge idea is great! Ill have to get a caliper and use it too. Mine is just an easy solution to an age old question, works well for me :).
|
If you have a diamond file, you can score the glass with it and snap it. No worry about power tools.
Joan |
great tip, I was wondering if I could use my Dremel to cut glass and you've answered that too!!
|
Nice tip! Maybe I will try it if I am trying to make a set. I just use my little mm sliding tool and measure it, LOL.
Boy am I jealous of your torch, you lucky girl! |
When I made the big jump into buying some boro tubes and rods, I realized I had no idea how to cut them (I'd never cut the moretti, they just seemed an ok size already). My husband put one of our dremel bits that is a tungsten carbide bit into a table vise, and I just go over there and scratch them 3/4 of the way around. Then, according to the genius Homer Hoyt, I wet the spot on the tube or rod and touch it with a molten rod at the scratch. You hear a little crack, and it makes a great even crack all around. Works every time, nice even cuts!
|
Shepherd Thanks I'm going to start tubing soon needed that info
|
Great Tip!
|
These are all great ideas! I hope y'all don't mind if I interject a safety tip?
Cutting, breaking and snapping rods creates glass dust. Please make sure that you don't inhale the stuff. Wash your hands afterwards and use a damp cloth to safely remove the dust from your work surface. Be careful out there! :cool: |
Thanks so much! I have been trying to figure out how to make matching earrings since I started and nothing seems to work very well. I will try this.
|
Great Tip, Tess! Thanks :)
|
Awesome tip! Thanks a million. I'll try it real soon.
|
Quote:
|
NO WAY! They're the ones who taught me the dangers of glass dust.
|
All times are GMT -7. The time now is 7:19am. |
Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.