|
Tips, Techniques, and Questions -- Technical questions or tips |
2017-06-19, 11:22am
|
Junior Member
|
|
Join Date: Jun 16, 2016
Posts: 18
|
|
Trick to have release in the middle of mandrel without coating all the way to the end
Is there a trick to just have bead release coating the middle of a mandrel without having to dip most of the mandrel and then wiping off the end? So far, I have not come up with a clever mess free way...
|
2017-06-19, 11:38am
|
|
Phill
|
|
Join Date: Mar 21, 2009
Location: Winnebago, MN
Posts: 2,489
|
|
I have heard some say the trick is to use a wide spatula with bead release dipped in an open mouth container.
Getting a smooth, even layer would be hard for me free handed so I would likely brace one end of the mandrel on something and probably my spatula hand as well.
Others just go for the long, tall bottle and wipe the end off with their fingers.
It's not all that messy, especially if you have a second open mouth container to wipe the excess off your fingers on the edge.
I would find cleaning the excess off the spatula more troublesome than my fingers.
Good luck and let us know what works for you.
I have just learned to switch hands with the one clean end but I also have an electric mandrel spinner and so my hands don't tire of doing the same motion for twenty minutes while pretend to be an artist with molten glass.
__________________
The Zombie Apocalypse is Upon Us.
|
2017-06-19, 12:31pm
|
|
Senior Member
|
|
Join Date: Jun 22, 2005
Location: west of Atlanta, Georgia
Posts: 5,371
|
|
Just use a jar lid like mayo, cleaned. pour in the release and it's easy to do the mandrel in the center.
|
2017-06-19, 2:43pm
|
|
Miata and Sunshine! Yay!
|
|
Join Date: Aug 19, 2007
Location: Lower left coast of FL
Posts: 1,622
|
|
I use a large plastic lid and clip a notch out of each side directly across from each other, pour a small amount (up to the bottom of the notch) of release onto the lid and put your mandrel into the notches and roll it in the release. No messy hands and you can pour the remainder back into the bottle by cupping the plastic a little.
__________________
I have enough money to last me for the rest of my life.....unless I buy something.
RED Mega Minor on Bulk propane and 1 5lpm + 10lpm oxycons waaaay high up in the mountains of SW Florida To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Contributing member of the EPIC FLOUNCE thread 2013
Proud member of YOU PEOPLE thread.
|
2017-06-19, 4:37pm
|
|
Senior Member
|
|
Join Date: Sep 18, 2005
Location: Wyoming
Posts: 1,989
|
|
Huh. I'da just dipped it as far as I could then used my fingers to wipe off the excess on the opposite end. But I'm lazy that way.
__________________
Darleen
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2017-06-19, 4:49pm
|
|
SCIENCE Teacher!
|
|
Join Date: Jul 19, 2005
Location: Wylie, TX
Posts: 2,140
|
|
I deep dip all my mandrels with the release. I have some nerve damage in my hands and I can feel the bead release coated end better than the non-coated end. On hand problem days this means I rarely ever drop the mandrel.
__________________
Yes, I am FosterFire Bead Release.
|
2017-06-20, 7:07pm
|
Senior Member
|
|
Join Date: Sep 13, 2005
Location: New Jersey
Posts: 815
|
|
Use a foil loaf pan. In the center of each side cut a slot almost the depth of the pan. Put release in pan to bottom edge of slots. Mandrel goes in to slots with pan in center of mandrel. Roll the mandrel in the release and refill frequently.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Still selling beadstands but no more Puffy Mandrels.
|
2017-06-21, 12:56pm
|
Member
|
|
Join Date: Sep 11, 2016
Location: Vancouver WA
Posts: 70
|
|
I put the mandrel horizontally across the bead release jar opening and use a tablespoon to drip in onto the middle of the mandrel while rotating the mandrel. The run off falls back into the jar. Easy.
|
2017-07-11, 9:25am
|
Senior Member
|
|
Join Date: Apr 17, 2006
Posts: 146
|
|
I have always used middle dipped mandrels since lamping 95% of the time; as I do a lot of sculpture working beads. I use a tall jar balsamic vinegar bottle on my second; first one broke. I dip my mandrel in about 3/4ths take it out and dip in glass of water and stir to remove extra bead release on the lower part of mandrel which leaves the middle still with bead release. Than I place in can of sand to dry. Once I am done dipping and stirring I save the water with the small amount bead release pour it in a jar with lid.
Next time I dip I pour the water into my glass but save the watered down bead release at the bottom of jar to add to my vinegar jar or main bottle of bead release; I do not let much if any of the watered down saved bead release get poured into my glass I will be stirring away the newly dipped mandrels..... this way I do not lose much bead release ever ( only when I drop the blasted bottle and it breaks) LOL
__________________
Pam
beadforever
|
2017-07-11, 3:05pm
|
Member
|
|
Join Date: Feb 25, 2009
Posts: 40
|
|
I have worked the middle of the mandrel for 15 years and I simply take a spoon, get it as full of bead release as you can...rest it on the open top of the bead release container and then roll the mandrel in the release. I can usually do about 8 or 10 mandrels before I scoop up more bead release. Sometimes I get a little bump or blob and this goes away when I lightly tap the mandrel against my hand. All very easy. Ernie Wagner
|
2017-07-11, 5:31pm
|
|
Fried Cat
|
|
Join Date: Jan 02, 2011
Posts: 665
|
|
Quote:
Originally Posted by Jeri
Use a foil loaf pan. In the center of each side cut a slot almost the depth of the pan. Put release in pan to bottom edge of slots. Mandrel goes in to slots with pan in center of mandrel. Roll the mandrel in the release and refill frequently.
|
This.
|
2017-07-11, 9:20pm
|
|
Senior Member
|
|
Join Date: Nov 01, 2006
Location: Nth NSW, Australia
Posts: 879
|
|
Use a second jar with just water in it.
Dip mandrel to centre
Dip in water to remove the excess on the end
Release can be reclaimed for re-use when left to settle and excess water carefully tipped off.
__________________
Nicole
Custard...it's just like hot icecream!
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 2:35pm.
|