|
2011-05-11, 5:41pm
|
|
Senior Member
|
|
Join Date: Jan 11, 2007
Location: Eastern NC.
Posts: 4,304
|
|
How I make fused copper jump rings!
I made this short tutorial today on how I make fused copper jump rings. I hope you enjoy!
Step 1.
Using round object, wrap around several inches of 16-gauge copper wire.
The length of copper wire depends on the size and amount of the jump
rings needed.
Step 2.
Using flush-nose cutters, cut each ring from the coil just made.
Step 3.
If needed, file both ends of the jump ring. Do not pull the jump rings
open as this will misshape the rings. Using a side to side motion close
each jump ring until both ends are completely touching and there is no
gaps or spaces.
Step 4.
Have a bowl of cool water in reach while fusing. Light the torch and hold
the copper jump ring with an old pair of tweezers.
Wave the jump ring in the flame to heat the entire piece. Place the cut
section of the jump ring into the tip of the blue cone in the flame. This is
the hottest part of the flame!
The ends will start to glow red and you will notice them melting or fusing
together. This can happen quickly so you will need to be ready. The cut
section will suddenly disappear once its fused as shown in the second
photo. Quickly remove from the ring from the flame and put in the cool
water.
Step 5.
Put the jump rings in pickle to remove all the dark fire scale.
I use a homemade version! Mix a 1/2 cup of water and 1/2 of vinegar in
an old sauce pan or metal bowl. Heat the mixture to a slow simmer, and
add a teaspoon of table salt. Add your jump rings to the pickle and let
simmer on the lowest heat for 1-2 minutes. Remove the rings with
tweezers and rinse!
In this photo is 3 jump rings after they have been fused and cleaned using
the homemade pickle. Inside the black marks at the top of each ring is
the section of the jump ring that was fused together.
Step 6.
The jump rings will be very soft! Using a chasing-hammer and steel-block
or anvil, gently hammer each ring to flatten and harden. You may also
tumble in a tumbler for several hours if you don't want the rings
flattened.
__________________
Jewlie or Julie, its all the same. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. My Facebook
|
2011-05-11, 5:45pm
|
|
Ass-kicking Cephalopod
|
|
Join Date: Jun 19, 2006
Location: Duh, Squidville
Posts: 9,523
|
|
Very cool! Thank you!
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
DOG is my co-pilot
Cricket w/two 5 lpm oxycons - and sometimes a Minor.
|
2011-05-11, 5:45pm
|
|
I fart diamonds
|
|
Join Date: Jun 14, 2005
Location: Altamonte Springs, FL
Posts: 3,893
|
|
Thank you!
__________________
-Shawnette the original "everybody get a grip" girl
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-11, 5:48pm
|
|
Experimentalist
|
|
Join Date: Nov 15, 2005
Location: Penryn, California
Posts: 6,758
|
|
Wonderful, Julie! Thanks for sharing!
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-11, 5:55pm
|
|
Senior Member
|
|
Join Date: Jan 11, 2007
Location: Eastern NC.
Posts: 4,304
|
|
I have it in a pdf file if anyone would like it sent to their e-mail address. Just pm me and I'll send it. Wasn't sure how to post the pdf directly for anyone to get.
__________________
Jewlie or Julie, its all the same. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. My Facebook
|
2011-05-11, 5:58pm
|
|
Senior Member
|
|
Join Date: Jan 11, 2007
Location: Eastern NC.
Posts: 4,304
|
|
I forgot to mention that I'm using my "Hot Head" torch to fuse with.
__________________
Jewlie or Julie, its all the same. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. My Facebook
|
2011-05-11, 6:04pm
|
|
KLH Design Studio
|
|
Join Date: Jun 12, 2005
Location: Ontario, Canada
Posts: 469
|
|
Thanks for sharing this, Julie! =]
__________________
~~Karen ~~
"Chase the dream, not the competition" ~
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. ~ To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. ~ To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. ~ To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. ~ To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. ~
|
2011-05-11, 6:07pm
|
|
Senior Member
|
|
Join Date: Feb 15, 2006
Location: In my Studio
Posts: 1,811
|
|
Thank you so much for taking the time to make this and post it.
Janet C.
|
2011-05-11, 6:12pm
|
|
Hobby Junkie
|
|
Join Date: Dec 08, 2009
Location: Perkasie, PA
Posts: 1,967
|
|
Awesome Julie! You rock! Have you tried making a fused chain with them??? Just wondering how that would work.
__________________
Cori C-R
PS - This is what part of the alphabet would look like if Q and R were eliminated.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-11, 6:24pm
|
|
Senior Member
|
|
Join Date: May 30, 2006
Location: NC
Posts: 913
|
|
Wow thanks for posting this. Awesome job.
__________________
"When life hands you lemons reach for the Tequila"
Donna
|
2011-05-11, 6:27pm
|
|
Senior Member
|
|
Join Date: Jan 11, 2007
Location: Eastern NC.
Posts: 4,304
|
|
Yes I have Cori! I fuse a jump ring then add another and fuse it. I keep repeating this until its long enough. You will need to have an extra pair of tweezers or old pliers to hold the chain out of the flame while you are fusing. I didn't try making chains until I had lots of practice making the jump rings. I burned through many jump rings before I got the hang of it. LOL
__________________
Jewlie or Julie, its all the same. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. My Facebook
|
2011-05-11, 6:28pm
|
|
Senior Member
|
|
Join Date: Jan 11, 2007
Location: Eastern NC.
Posts: 4,304
|
|
Thanks everyone!!!
__________________
Jewlie or Julie, its all the same. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. My Facebook
|
2011-05-11, 7:13pm
|
|
Senior Member
|
|
Join Date: Jun 16, 2005
Location: Maple Valley WA
Posts: 7,064
|
|
Cool, that looks easy.
__________________
Lara
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. ** To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. ** To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Become a fan on Facebook: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-11, 7:37pm
|
|
Member
|
|
Join Date: Jun 13, 2007
Location: Beautiful Vancouver Island
Posts: 58
|
|
Perfect timing, thanks lots!!
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-11, 7:57pm
|
|
Ass-kicking Cephalopod
|
|
Join Date: Jun 19, 2006
Location: Duh, Squidville
Posts: 9,523
|
|
So, what kind of cutter is that you're using? Does it cut both sides flush?
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
DOG is my co-pilot
Cricket w/two 5 lpm oxycons - and sometimes a Minor.
|
2011-05-11, 8:01pm
|
|
Senior Member
|
|
Join Date: Jan 11, 2007
Location: Eastern NC.
Posts: 4,304
|
|
Its a Harbour Freight special! It cuts one side flush but the other side is angled. I have to do a little filing but not much.
__________________
Jewlie or Julie, its all the same. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. My Facebook
|
2011-05-11, 8:14pm
|
|
Ass-kicking Cephalopod
|
|
Join Date: Jun 19, 2006
Location: Duh, Squidville
Posts: 9,523
|
|
Cool - thanks!
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
DOG is my co-pilot
Cricket w/two 5 lpm oxycons - and sometimes a Minor.
|
2011-05-11, 8:17pm
|
|
It's about having fun!
|
|
Join Date: Sep 30, 2010
Location: Arizona
Posts: 552
|
|
Thank you for sharing!
__________________
The Boneyard Punch Tutorial: Learn how to make a simple tool that will easily put a hole in hot glass! It really works! See my Etsy!
My Etsy: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. Thank you! Joni
|
2011-05-11, 8:31pm
|
|
Formerly FishBulb
|
|
Join Date: Dec 05, 2008
Location: Pony Flower Princess Land
Posts: 2,772
|
|
This is just perfect! Thank you so much for posting it!
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
In Soviet Russia, Google searches you.
|
2011-05-11, 9:54pm
|
beads....mmmm
|
|
Join Date: Jul 06, 2005
Location: WA
Posts: 1,871
|
|
Wow, thanks! Silly question - does this work with silver, too?
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. :: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. :: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. :: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. ::
|
2011-05-11, 10:12pm
|
|
Senior Member
|
|
Join Date: Sep 15, 2006
Location: Port Charlotte Florida
Posts: 259
|
|
Thank you for sharing this with us! Uh Oh something new to try.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-12, 12:07am
|
|
I speak Murrini!
|
|
Join Date: Oct 12, 2006
Location: In a Glass House, CA
Posts: 9,170
|
|
Oh, my! This is WONDERFUL!!! Smooches to you for sharing, and the pictures are GREAT! I use this same technique to fuse my Pure Silver jump rings, except I use a tiny "pencil torch" to do a fine point flame. They are also very inexpensive; I got mine on eBay for just a couple bucks! ( http://cgi.ebay.com/Butane-Pencil-To...item230f645996)
And I have a Hot Head too! I can't wait to try this out!!!
__________________
~DeAnne~
I've got a murrini for that,'ya know! To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
"Only a fool rushes to his own demise..." ~Zorro
|
2011-05-12, 1:31am
|
|
Resident hippie
|
|
Join Date: Mar 06, 2008
Location: Co Dublin Ireland
Posts: 2,733
|
|
Wow thanks Jewlie! I've also just ordered a pencil tip butane torch from eBay - thanks DeAnne! So De - can you also fuse fine silver wire ringsd without solder using this technique?
__________________
Anna To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Have FUN!!!!! It's not about perfection..... Leslie - [not so] Crazy Woman
.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-12, 2:35am
|
Senior Member
|
|
Join Date: Mar 11, 2010
Posts: 138
|
|
Thanks Jewlie! I've done this with fine silver (no need to pickle), but hadn't thought of using copper. Definitely will try this out asap.
__________________
Karen To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-12, 4:28am
|
Senior Member
|
|
Join Date: Jun 29, 2005
Location: South Africa
Posts: 636
|
|
Thanks very much, I was just searching the net for copper solder now I don't need it yay!
|
2011-05-12, 6:47am
|
|
Senior Member
|
|
Join Date: Jun 30, 2005
Location: Central TX
Posts: 385
|
|
Thanks for sharing this-I love it. It inspires me to get to my jeweler's bench! Your the best!
__________________
Stefanie
Phishstuff by Stef
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-12, 6:53am
|
|
pedal as fast as you can
|
|
Join Date: Feb 06, 2010
Location: Ocala, FL (but my hearts in SF)
Posts: 210
|
|
Thanks Julie
Great Tutorial. I will be giving that a try !
Not to be a spoiler but, ventilation should be considered as well, copper fume is a bit toxic.
__________________
Craig
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2011-05-12, 7:59am
|
|
Senior Member
|
|
Join Date: Jan 11, 2007
Location: Eastern NC.
Posts: 4,304
|
|
Thanks everyone!
I don't think the pencil torch will work on the copper. The flame may be hot enough but it doesn't heat up a large enough area to melt the copper. You need a larger flame to keep the ring hot enough if that makes sence. I use my hot head for this. You can also burn or over heat the copper and it becomes brittle. You will have to play around with this to see what works best for you.
__________________
Jewlie or Julie, its all the same. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. My Facebook
|
2011-05-12, 8:01am
|
|
Senior Member
|
|
Join Date: Jan 11, 2007
Location: Eastern NC.
Posts: 4,304
|
|
Thank you Craig! Yes ventilation is important with this!
__________________
Jewlie or Julie, its all the same. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. My Facebook
|
2011-05-12, 10:46am
|
|
Senior Member
|
|
Join Date: Sep 17, 2008
Location: NH
Posts: 126
|
|
I heart you juliebees!!! This is an awesome tut!!! Thank you so much for sharing with us.
Big Hugs!!
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. gail To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Cricket w/ 5 lpm Oxycon
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 4:57pm.
|