|
Tips, Techniques, and Questions -- Technical questions or tips |
2014-07-21, 3:53pm
|
|
Senior Member
|
|
Join Date: Jun 23, 2005
Location: Up and down I-95
Posts: 4,390
|
|
Need to see if your kiln is the correct temp? Links for thermocouples
__________________
Rebecca
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-07-21, 4:02pm
|
|
Ass-kicking Cephalopod
|
|
Join Date: Jun 19, 2006
Location: Duh, Squidville
Posts: 9,523
|
|
I highly recommend checking temps too - my straight from the factory kiln was over 150 degrees off.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
DOG is my co-pilot
Cricket w/two 5 lpm oxycons - and sometimes a Minor.
|
2014-07-21, 5:38pm
|
|
Senior Member
|
|
Join Date: Jun 23, 2005
Location: Up and down I-95
Posts: 4,390
|
|
That's quite a bit! So what did you do? Do you just adjust the temp or calibrate it somehow?
__________________
Rebecca
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-07-21, 5:46pm
|
|
Ass-kicking Cephalopod
|
|
Join Date: Jun 19, 2006
Location: Duh, Squidville
Posts: 9,523
|
|
Quote:
Originally Posted by Three Muses Glass
That's quite a bit! So what did you do? Do you just adjust the temp or calibrate it somehow?
|
They sent me a new circuit board for the controller, and that got it closer, but it's still about degrees off. At that point, I said screw it and just adjusted it.
I have a whole long thread about using Van Gogh glass that led to the discovery.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
DOG is my co-pilot
Cricket w/two 5 lpm oxycons - and sometimes a Minor.
|
2014-07-22, 4:08pm
|
Member
|
|
Join Date: Jun 13, 2007
Posts: 43
|
|
Quote:
Originally Posted by squid
They sent me a new circuit board for the controller, and that got it closer, but it's still about degrees off. At that point, I said screw it and just adjusted it.
|
We have found that the controllers are consistently accurate. In fact they are more accurate than the portable pyrometers. When the temperature is off, it is usually the thermocouple.
Sincerely,
Arnold Howard
Paragon Industries, L.P., Mesquite, Texas USA
ahoward@paragonweb.com / www.paragonweb.com
|
2014-07-22, 5:23pm
|
|
Ass-kicking Cephalopod
|
|
Join Date: Jun 19, 2006
Location: Duh, Squidville
Posts: 9,523
|
|
Quote:
Originally Posted by Arnold Howard
We have found that the controllers are consistently accurate. In fact they are more accurate than the portable pyrometers. When the temperature is off, it is usually the thermocouple.
Sincerely,
Arnold Howard
Paragon Industries, L.P., Mesquite, Texas USA
ahoward@paragonweb.com / www.paragonweb.com
|
I did also get a new thermocouple. I don't really remember what got it closer - I just know it never got completely fixed, so I just adjusted.
ETA - I went and found my thread about it - I had two thermocouples in addition to the new controller.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
DOG is my co-pilot
Cricket w/two 5 lpm oxycons - and sometimes a Minor.
|
2014-07-28, 6:22am
|
|
hyperT
|
|
Join Date: Jan 31, 2013
Location: San Antonio, Texas
Posts: 582
|
|
Calibrate a kiln using Ceramic Cones. Ceramic Cone #022 can be used to calibrate your kiln or check it for accuracy. 022 bends at 1087 F. Look this up on the net for more info on how to use them to calibrate your kiln. Glass Alchemy has a page on it too. Also when the kiln is cool it should be set to room temperature not 0. As this can effect the pyrometer.
This can also be done by using a suspended rod of glass if you know the bending point of that particular glass. It should be pretty close to accurate.
Ceramic cones are the most accurate.
|
2014-07-28, 8:55am
|
Member
|
|
Join Date: Mar 08, 2014
Posts: 49
|
|
Or you can coat a piece of glass with carbon. Carbon burns off at around 1050 F. Which is the annealing temp for boro. I always coat my piece to make sure it reached annealing temperature.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 2:32pm.
|