|
Safety -- Make sure you are safe! |
2007-11-01, 9:46pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
Ventilation Complete - Check it out!
I have one of these
http://www.homedepot.com/webapp/wcs/...ctId=100088166
1600 CFM's
hooked up to some ducting exhausting out the window.
I know 1600 is moving a lot of air but is the ducting to far away from my face and working area? Do you need a hood to have proper ventilation?
Give me some feed back? I'm just a dumb guy with a big torch...
|
2007-11-02, 8:01am
|
|
Gentleman of Leisure
|
|
Join Date: Jun 10, 2005
Location: A Little Bit West of Yosemite Valley
Posts: 5,200
|
|
You need a hood...... 1600cfm means nothing if system does not have good capture area (hood)... Also what is your make up air source?...
Quite frankly my opinion is that, that fan is probably one of the worst you could choose for powered ventilation.........
Dale
__________________
You can lead a person to knowledge, but you can't make them think. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Vendor-Artist-Studio-Teacher Registry To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
San Francisco - A Few Toys Short of a Happy Meal
|
2007-11-02, 10:43pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
I have an open window in another room. I realize I need a hood. Why do you dislike the fan?
|
2007-11-03, 10:18am
|
|
Gentleman of Leisure
|
|
Join Date: Jun 10, 2005
Location: A Little Bit West of Yosemite Valley
Posts: 5,200
|
|
Its big, inefficient and rating of fan is questionable.... I prefer centrifugal blowers that have motor out side hot air stream......
Propeller fans are for applications where its only necessary to make some air movement.... Its good to remove warm air from attic but I would not trust my health on it....
Dale
__________________
You can lead a person to knowledge, but you can't make them think. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Vendor-Artist-Studio-Teacher Registry To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
San Francisco - A Few Toys Short of a Happy Meal
|
2007-11-03, 4:00pm
|
Lampworker
|
|
Join Date: Jul 06, 2007
Location: Oregon
Posts: 211
|
|
need hood and side walls...or else the air will be pulled from all directions. you want it directed past you, across the torch and out.
|
2007-11-04, 12:26pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
can you link me to some better fans/hoods for sale and maybe some diagrams of good ventilation systems that I could apply to my current schema.
|
2007-11-04, 1:10pm
|
|
old fart
|
|
Join Date: Apr 18, 2006
Location: st paul mn
Posts: 778
|
|
here is one at the same store that will work great. i have been using one of these on my lampworking hood for quite a while. i used some duct adaptors to get a round duct on both sides of the fan.
http://www.homedepot.com/webapp/wcs/...3&ddkey=Search
__________________
Mark Wilson
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-11-04, 8:42pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
any other input? I've switched ends of my workbench now so that I'm closer to the window and I can create a hood that will go right out to the window. What do you guys thinks is the appropriate size hood for a gtt mirage?
|
2007-11-04, 9:58pm
|
|
Senior Member
|
|
Join Date: Oct 31, 2007
Location: Alberta Canada
Posts: 116
|
|
I would be interested in this as well, I was just about to purchase me exhaust system, but I didn't know I needed a hood, does anyone have any pictures that would illustrate how that would work with a fan system such as above?
|
2007-11-05, 8:11am
|
|
old fart
|
|
Join Date: Apr 18, 2006
Location: st paul mn
Posts: 778
|
|
here are some photos showing how to use the fan i suggested. i made my ventilation hood using a similar fan (it is the blue fan mounted on top of my hood, almost the same as the yellow stanley fan i linked to). i bought the cheapest hood if could find, got rid of the wimppy fan it came with, drilled a big hole in the top where i mounted the inlet to the fan, and then used some retanuglar to round duct adaptors to get the output into the duct to the outside. then i used cement wallboard to box in the sides and back of the hood so that i get more effective ventilation as well as a nice fireproof surounding. here is a link.
http://www.lampworketc.com/forums/sh...ad.php?t=67463
__________________
Mark Wilson
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-11-05, 5:54pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
hey dale,
hey do you mind talking via email about proper ventilation. I just want to be safe and I had a nose bleed the other night. I haven't blown glass since and I'm going to rework everything and was hoping to utilize your advice.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-11-05, 8:17pm
|
|
Gentleman of Leisure
|
|
Join Date: Jun 10, 2005
Location: A Little Bit West of Yosemite Valley
Posts: 5,200
|
|
There has been thousands of words written in dozens of threads on many boards........ I doubt I can say anything that has not already been said...
Dale
__________________
You can lead a person to knowledge, but you can't make them think. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Vendor-Artist-Studio-Teacher Registry To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
San Francisco - A Few Toys Short of a Happy Meal
|
2007-11-06, 10:25pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
Am I on to something here or should I totally rework this? I bought an ecco or echo or eco or something 800 cfm fan. MY hoot is going to be somewhere in the ballpark of 900 sq in so 6.5 sq ft which comes out between 750 - 900 recommended cfm by your calculations dale... Am I right?
I'm worried now that the fan will get to hot what do you think?
I'm thinking this is a vast improvement... critique please
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-11-07, 9:23am
|
|
Gentleman of Leisure
|
|
Join Date: Jun 10, 2005
Location: A Little Bit West of Yosemite Valley
Posts: 5,200
|
|
Conceptually you are going in righ direction... More pictures as you progress... Remember its the functionality of hood that is important...
Actually the width/height comes closer to 720 sq-in ( 24x30 =720)
So that is divided by 144 to get 5 sq ft ( 720/144=5)
5 sqft multiplied by 125cfm, (per sqft -standard) is 625cfm..
With fan you have selected it looks like you are on track...
You could move fan to window where air has cooled somewhat and connect from hood to fan with duct.. There no rules that says fan has to be at hood, it just has to be in "system".
Dale
__________________
You can lead a person to knowledge, but you can't make them think. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Vendor-Artist-Studio-Teacher Registry To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
San Francisco - A Few Toys Short of a Happy Meal
|
2007-11-07, 5:48pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
I'd like some pointers and suggestions please or things I should absolutely *not* do?
Is it bad to use galvanized sheet metal or tin or any of the metals I'm using as a barrier? Will they possibly get to hot and cause damage or let off gases that will be harmful?
Will taping the seams with the foil tape work well to make the hood air tight? Or will that stuff burn right off?
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-11-07, 8:10pm
|
|
Gentleman of Leisure
|
|
Join Date: Jun 10, 2005
Location: A Little Bit West of Yosemite Valley
Posts: 5,200
|
|
If hood gets hot enough to off gas (from galvanized sheet metal) or melt you foil tape, something is definitely wrong.... Galvanized or tin plate is metal of choice for almost all ventilation work....
Just make it airtight and then test your work...
Yes surfaces will get warm but probably not so hot you can lay hand on it and keep it there while fan and torch are in operation ..
Dale
__________________
You can lead a person to knowledge, but you can't make them think. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Vendor-Artist-Studio-Teacher Registry To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
San Francisco - A Few Toys Short of a Happy Meal
|
2007-11-07, 8:46pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
What is the best way to test the ventilation? I did some searches and couldn't come up with anything good. Care to share?
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-11-07, 10:01pm
|
|
Senior Member
|
|
Join Date: Jul 12, 2006
Location: DFW, TX
Posts: 917
|
|
The first test would be to roll up some paper towels tight and light one end on fire then blow it out. This produces a nice amount of smoke to test with. I used some metal clamps to hold a smoldering towels in the possitions of each torch on the bench and sat and watched what happened to the smoke.
__________________
Paul Ewing
Torch Ho... GTT Mirage, Carlisle CC, GTT Cheetahs, GTT Lynxes, and others on tanked O2.
|
2007-11-18, 12:58pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
Is there any benefit to where the fan is attached to the hood for removing air? Like the back middle, middle middle, back left. any performance issues like that?
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-11-25, 10:52pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-11-26, 12:52pm
|
|
Curmudgeon Engineering
|
|
Join Date: Feb 15, 2006
Location: Near Seattle, WA
Posts: 1,723
|
|
Vent system test
There is a test suggested on another board that is similar to the smoking paper test.
Fire up the torch as you would be using it.
Sit or stand where you would normally be.
Burn a small piece of bacon in the flame.
If you can smell any bacon smell it's not good enough.
PJH
|
2007-11-29, 11:10pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
No comments eh? Really?
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-11-30, 2:09am
|
Senior Member
|
|
Join Date: Nov 19, 2007
Posts: 1,078
|
|
This is an awesome hood! I recently made a vent hood as well and was worried about the heat transfer from the torch but I fired it up tonight and there was no problem! Although the flame does get fairly close to the galvanized metal on the top of the hood, it didn't get broiling hot - just warm to the touch.
I love the way your torch is INSIDE this vent - no hope of fumes escaping there!
Great job. Let us know how it works for you...
|
2007-11-30, 2:55pm
|
Senior Member
|
|
Join Date: Mar 03, 2006
Location: San Francisco Peninsula, CA
Posts: 1,034
|
|
The hood itself is fantastic!
I do have a question about where the fumes go when they exit the system? And where is your make up air?
-Diane
__________________
-Diane
My Facebook business page: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
GTT Bobcat or Carlisle Lucio on an Integra 10
(and sometimes I pull out my HotHead!)
|
2007-12-01, 1:44am
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
The fumes are going out the window and into the sky. I have a room, 3 rooms down, (45 - 50ft) with a window open and all doors open on their way back to my room.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-12-04, 9:58am
|
Senior Member
|
|
Join Date: Mar 03, 2006
Location: San Francisco Peninsula, CA
Posts: 1,034
|
|
I understand that the fumes are being vented outside - what I'm curious about is if the exit port of the ducting is surrounded by anything, or if it is just blowing out an open window. It's hard to see what's going on with the closed blinds over the window.
-Diane
__________________
-Diane
My Facebook business page: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
GTT Bobcat or Carlisle Lucio on an Integra 10
(and sometimes I pull out my HotHead!)
|
2007-12-04, 11:39am
|
|
Gentleman of Leisure
|
|
Join Date: Jun 10, 2005
Location: A Little Bit West of Yosemite Valley
Posts: 5,200
|
|
For system to work effectively window needs to be sealed against blowback ( gases coming back in around end of duct)...
Its easy to do.... have a piece of acrylic or ply wood or whatever with holes in it for duct... Put it in place during "work" time, remove it when done, just be sure it "seals".. Foam weather stripping tape does a wonderful thing here...
Dale
__________________
You can lead a person to knowledge, but you can't make them think. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Vendor-Artist-Studio-Teacher Registry To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
San Francisco - A Few Toys Short of a Happy Meal
|
2007-12-04, 11:50am
|
Senior Member
|
|
Join Date: Mar 03, 2006
Location: San Francisco Peninsula, CA
Posts: 1,034
|
|
Dale - that's exactly what I was concerned about. Thank you for putting it into words for me.
-Diane
__________________
-Diane
My Facebook business page: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
GTT Bobcat or Carlisle Lucio on an Integra 10
(and sometimes I pull out my HotHead!)
|
2007-12-04, 6:36pm
|
i need help
|
|
Join Date: Oct 17, 2007
Location: slc
Posts: 55
|
|
Well I have a piece of ply that the vent fits through pretty snugly and then i use a piece of 2x4 to put pressure on the wood so it stays snug. It's not perfect but that's my next improvement.
I'm in the process of buying a house so I can make things more permanent and not have to hide things from the land lord!
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2007-12-04, 6:53pm
|
Senior Member
|
|
Join Date: Mar 03, 2006
Location: San Francisco Peninsula, CA
Posts: 1,034
|
|
Sounds like a great plan! Thanks for clarifying this.
-Diane
__________________
-Diane
My Facebook business page: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
GTT Bobcat or Carlisle Lucio on an Integra 10
(and sometimes I pull out my HotHead!)
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 2:27am.
|