|
Safety -- Make sure you are safe! |
2005-08-10, 6:29pm
|
|
Pobody's nerfect!
|
|
Join Date: Jul 14, 2005
Location: nashville
Posts: 550
|
|
MAPP gas
hi everyone
well so I've been lampworking for almost two weeks. using an HH with mapp gas, and I'm still pretty nervous about the safety issue, so any answers will be much appreciated.
1. how do i dispose of empty canisters?
2. how important is storing canisters upright. I just noticed the bottle i had in the garage had been lying on its side, and also noticed that the metal on part of the top of the canister is slightly rough, as if the roughness resulted from the bottle lying on its side with liquid touching that portion??? so is that bottle damaged in any way, or is it just a coincidence?
3. what is actually happening when the bottom of the canister gets cold and starts to sweat after torching for awhile? is it dangerous to operate in this condition, or just wasteful?
TIA!!!
__________________
Sherri
"While we have the gift of life, it seems to me the only tragedy is to allow part of us to die -- whether it is our spirit, our creativity or our glorious uniqueness” -- Gilda Radner
|
2005-08-10, 7:41pm
|
|
Gentleman of Leisure
|
|
Join Date: Jun 10, 2005
Location: A Little Bit West of Yosemite Valley
Posts: 5,200
|
|
Quote:
Originally Posted by shesmi
hi everyone
well so I've been lampworking for almost two weeks. using an HH with mapp gas, and I'm still pretty nervous about the safety issue, so any answers will be much appreciated.
1. how do i dispose of empty canisters?
2. how important is storing canisters upright. I just noticed the bottle i had in the garage had been lying on its side, and also noticed that the metal on part of the top of the canister is slightly rough, as if the roughness resulted from the bottle lying on its side with liquid touching that portion??? so is that bottle damaged in any way, or is it just a coincidence?
3. what is actually happening when the bottom of the canister gets cold and starts to sweat after torching for awhile? is it dangerous to operate in this condition, or just wasteful?
TIA!!!
|
1. Completely empty conisters are disposable in "normal" trash pickup/disposal (do not burn).
2. Canisters should be stored upright. Normally a canister on it's side is not a problem, but upright is desirable. Roughness on "seating" surface is probably moisture attacking the bare metal and causing a bit of rust. This can be cleaned off. If canister/torch form a good seal it is not a problem. If canister/torch will not seal- Do not attempt to use it.
3. As liquid fuel evaporate to a vapor, it cools the canister. As the canister cools it draws moisture out of the surrounding air and it condenses on out side of container. It happens, it is not a problem. It's same process that happens when you put cold soda can out on counter in warm room. Its also basic physics. Also note that as temperature drops inside canister the evaporation process slows down and vapor pressure will drop as canister gets cooler.
You may also be interested in first message this thread.
http://www.lampworketc.com/forums/showthread.php?t=831
Dale
__________________
You can lead a person to knowledge, but you can't make them think. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Vendor-Artist-Studio-Teacher Registry To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
San Francisco - A Few Toys Short of a Happy Meal
|
2005-08-10, 10:40pm
|
|
Pobody's nerfect!
|
|
Join Date: Jul 14, 2005
Location: nashville
Posts: 550
|
|
thanks dale - appreciate the answers -- this is all so new to me and i tend to obsess about little things
__________________
Sherri
"While we have the gift of life, it seems to me the only tragedy is to allow part of us to die -- whether it is our spirit, our creativity or our glorious uniqueness” -- Gilda Radner
|
2005-08-11, 5:54am
|
|
Safety ALWAYS
|
|
Join Date: Jun 10, 2005
Location: Sauk Rapids, Minnesota
Posts: 2,401
|
|
As far as #1 is concerned, check with your local garbage disposal company first. Here in Minnesota, one pound propane/MAPP cylinders are not allowed to be disposed of in regular garbage, they must be taken to a hazardous waste facility for disposal.
Minnesota has several large "consolidators" of garbage that gather waste from many communities, which is then trucked to either landfills or waste burners for incineration.
Additionall, what you may think of as an empty container may still yet contain some fuel gas. The only way to be absolutely sure it is empty is to remove the fill valve - it uses a similar insert as bicycle and car tires - removing this valve insert will allow any remaining fuel to escape - you can also put a plumbers torch head on the tank and let the remaining gas burn off.
But please, check with your garbage company FIRST before you dispose of them.
|
2005-08-11, 10:37am
|
|
Pobody's nerfect!
|
|
Join Date: Jul 14, 2005
Location: nashville
Posts: 550
|
|
I'm glad you mentioned the fact that the containers may not be empty, Mike, because I was wondering if that could be happening.
My DH suggested just putting the HH back on the canister and opening up the valve to get rid of what gas might be remaining, once everything cools down - but I wasnt sure about doing that. Is there a difference between doing that, and doing what you suggested with the fill valve or plummers torch head?
Sometimes I think I'm being overly nervous about all this, but i'd rather be that way than the way my DH is - who thinks nothing of filling the lawn mower with gas while the motor is running
__________________
Sherri
"While we have the gift of life, it seems to me the only tragedy is to allow part of us to die -- whether it is our spirit, our creativity or our glorious uniqueness” -- Gilda Radner
|
2005-08-11, 11:31am
|
|
Safety ALWAYS
|
|
Join Date: Jun 10, 2005
Location: Sauk Rapids, Minnesota
Posts: 2,401
|
|
It's far safer to burn it off - you can certainly use the hothead if you want - but don't just put the torch head on and open the valve - you may get localized pooling which could lead to an "explosive" situation.
|
2005-08-11, 11:40am
|
|
boro color bender
|
|
Join Date: Jun 06, 2005
Location: The Oregon coast!
Posts: 10,039
|
|
Unless you have a lot left, it's not going to pool in a well ventilated or large area and explode. I supose it's better to be safe than sorry, so just take it outside to vent off the left over gas. If you leave it open for a little while outside, it's safe.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
"Truth is, everybody is going to hurt you; you just gotta find the ones worth suffering for." -Bob Marley
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 5:30am.
|