|
Tips, Techniques, and Questions -- Technical questions or tips |
2016-04-13, 11:32am
|
Junior Member
|
|
Join Date: Dec 15, 2015
Posts: 4
|
|
Soldering multiple pearl posts - Help?
I'm working on a concept for a piece and I need to solder multiple pearl posts to it. Does anyone know how I can go about doing them either all at once or in groups? I'm also concerned with one's melting or falling as I'm working on others.
Ideas anyone?
|
2016-04-13, 1:15pm
|
Senior Member
|
|
Join Date: Feb 02, 2010
Posts: 3,476
|
|
If they're all on the same base piece, you're either going to have to get awfully good with a pinpoint flame and differing grades of solder or use a laser welder. The laser welder doesn't make any appreciable heat, so you could just go from one to the next. Of course, it also costs about $5000, so there is that.
__________________
ESC
Soft glass on a Minor/concentrator since 1996
|
2016-04-13, 1:28pm
|
|
Phill
|
|
Join Date: Mar 21, 2009
Location: Winnebago, MN
Posts: 2,489
|
|
When I was soldering electronic components back in the day...
We used needle nosed pliers with rubber bands around the handles and pinched the part we were soldering with them.
They would effectively steal the heat to keep it from going past the them and prevent other solder joints from coming loose.
If you are quick enough and the joints are clean and have flux to prevent the oxidation from spoiling the joint you can even use alligator clips but you do have to be rather quick as the thin metal of alligator clips don't soak up much heat.
Another trick you can do is to wrap previously soldered joints tightly with soft copper wire and you can then weave this wire from one joint to the next and the next with each one getting a good solid full wrap before going on to the next.
And other thought that just came to mind might be to try precious metal clay as a packing around already soldered joints. We did not have it back in my day but it is mostly metal powder and should wick the heat away. Just a thought. Good luck.
__________________
The Zombie Apocalypse is Upon Us.
|
2016-04-13, 2:06pm
|
Dix Harrison
|
|
Join Date: Mar 31, 2009
Location: KCKS - But my heart is in Scotland
Posts: 530
|
|
|
2016-04-13, 2:19pm
|
|
Lifelong Student
|
|
Join Date: Apr 13, 2014
Location: Washington USA
Posts: 2,676
|
|
I have soldered multiple posts before on a pendant. I drilled holes in the base piece that were just big enough to fit the post wires. I extended the post wires to the other side and stuck them into my fireblock. This kept them from moving. After soldering I trimmed off the excess and filed it smooth.
__________________
Norma
|
2016-04-13, 3:30pm
|
Senior Member
|
|
Join Date: Feb 02, 2010
Posts: 3,476
|
|
Dix, I may have to give the Chill Gel another go. I've tried it before without any luck, but maybe the next time the magic will happen.
__________________
ESC
Soft glass on a Minor/concentrator since 1996
|
2016-04-13, 4:36pm
|
|
Senior Member
|
|
Join Date: Oct 27, 2014
Location: North of Nowhere
Posts: 2,687
|
|
There's a solder board that is soft enough that it can be used as Mina described without drilling but I can't remember what it's called. I
|
2016-04-13, 4:56pm
|
|
Corgi Cult Member
|
|
Join Date: Jan 10, 2006
Location: Central Illinois
Posts: 3,723
|
|
How close together do they need to be?
When soldering posts, I find it helpful to add the solder to the post first, then add it to whatever it is getting soldered to, then heat to soldering point again to attach.
Can the piece lay flat? If so, that makes soldering close easier. If not, can you carve a channel in your soldering block to hold the piece at the desired level?
__________________
Kathy
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 5:07pm.
|